Home › Tools › Mouse Button Tester

Mouse Tester online

Test every mouse button — left, right, wheel and side buttons — plus scrolling, double-click faults, polling rate and clicks per second. Free, live and right in your browser.

🖱 5 buttons + wheel⚠ Double-click fault test📡 Polling rate (Hz)⚡ CPS test✓ Free, no install
Ready — click inside the test area
Colour:
CLICK, HOLD & SCROLL HERE
Buttons0 of 5 working
Test progress0%
Left buttonMain click0Not tested
Right buttonContext menu0Not tested
Middle / wheel clickPress the wheel down0Not tested
Back (side button 4)Thumb button, rear0Not tested
Forward (side button 5)Thumb button, front0Not tested
Scroll wheelUp / down · tilt left / right0Not tested
0Clicks / sec
0Best CPS
0Double-click faults
0Scroll up
0Scroll down
–Last hold (ms)
📱 No mouse found on this device. Touch taps are not counted, so the results stay accurate. Connect a USB or Bluetooth mouse, or open this page on a computer — the tester starts as soon as it detects a mouse.
⚠ Double-click fault test0 double-clicks

Click once at a time, normally. A healthy mouse never sends two clicks within a few milliseconds. If it does, the switch is wearing out.

Single-click here 10 times
Sensitivity80 ms
No faults detected yet.
Event log
  • Events appear here as you click and scroll.
📡 Polling rate testHz

Move your mouse quickly in circles inside the box. The tester counts how many position reports your mouse sends per second.

—Hz now
Average —Peak —Likely setting —
Move your mouse here
12525050010002000+

Browsers can cap or batch mouse reports, so treat this as an estimate. Your mouse software shows the exact setting.

⚡ Clicks per second (CPS) test

Click the box as fast as you can. The timer starts with your first click.

Click to startBest: —
5.0Seconds left
0Clicks
0.0CPS
Average people click 6–7 times per second.

How to test your mouse

One minute is enough to check every button.

01

Press every button

Click left, right, the wheel and both side buttons inside the dark area. Each one turns green when it works.

02

Scroll the wheel

Scroll up and down slowly. If the count jumps the wrong way, the wheel sensor may be dirty.

03

Check for double-clicks

Single-click the dashed box 10 times. Any fault above 0 means the switch is double-clicking.

04

Check polling rate & speed

Move the mouse in fast circles in the polling box, then try the CPS test for 1, 5 or 10 seconds.

What your results mean

Common problems and what to do.

⚠

Double-click faults

The left switch is worn. Try compressed air under the button, change the mouse’s double-click setting, or replace the switch or mouse.

✕

A button never lights up

Check the mouse’s own software (Logitech G Hub, Razer Synapse) — the button may be re-mapped. Try another USB port or browser.

↕

Scroll jumps the wrong way

Dust in the wheel encoder. Blow compressed air around the wheel while rolling it, then test again.

📡

Polling rate lower than expected

Check the setting in your mouse software, use a USB port directly on the PC, and move faster. Wireless mice may lower the rate to save battery.

⏸

Clicks sometimes don’t register

Low battery on wireless mice, or a weak USB receiver. Replace the battery and plug the receiver into a front port.

Frequently asked questions

Everything about testing a mouse.

What is a mouse tester?

A mouse tester is a free online tool that checks whether your mouse works properly — every button, the scroll wheel, double-click faults from worn switches, the polling rate and your clicks per second — without installing anything.

How do I check my mouse polling rate?

Move your mouse quickly in circles inside the Polling rate test box. The tester counts how many position reports arrive per second and shows the closest standard setting: 125, 250, 500, 1000 Hz or higher. Browsers can limit reports, so your mouse software shows the exact value.

What is a good polling rate?

125 Hz is standard for office mice. Gaming mice usually run at 1000 Hz, and some support 2000–8000 Hz. Higher rates make movement smoother but use more CPU and battery.

What is a good CPS score?

Most people click about 6–7 times per second. 8–10 CPS is fast, and over 10 CPS is very fast. Try the 1, 5 and 10-second tests — your best score is saved on this device.

How do I test my mouse buttons?

Move your pointer into the dark test area and press each button. The matching part of the mouse lights up, its counter goes up, and it is marked Working. Scroll the wheel up and down to test it too.

How do I know if my mouse double-clicks by itself?

Click normally with single, steady clicks. If the tool shows Double-click faults above 0, the mouse sent two clicks faster than a human can — a classic sign of a worn switch.

Why does my Back or Forward button not show up?

Some mouse software reassigns side buttons, and a few browsers handle them before the page sees them. Check your mouse app (Logitech, Razer, etc.), then try again in Chrome or Edge.

Does it work with wireless and Bluetooth mice?

Yes. Any mouse your computer recognises works, wired or wireless.

What is CPS?

Clicks per second — how fast you can click. Most people reach 6–8 CPS; gamers often reach 10 or more.

Can I test a laptop touchpad?

Yes. A tap or click is a left click, a two-finger click is a right click, and two-finger scrolling counts as the wheel.

Is anything recorded or sent anywhere?

No. The test runs entirely in your browser and nothing is saved or uploaded.

More free tools

Keyboard help and text tools.

Copied!